Skip to main content

Filter By:

  • Show More Sizes
  • Show Fewer Sizes

Wolf Tooth Components

Spoke Life Cycles is proud to carry Wolf Tooth components! Call us or Stop by to see our full selection.

$1.00
When using the GC 42 or GC 40 with a Shimano rear derailleur, a longer B-screw may be needed. This is a high quality 18-8 stainless steel M4 x 25 mm screw.
$1.00
Looking to get a little extra distance so that your derailleur clears your 40 or 42 tooth cog? Look no further. - M4 x 24mm screw for that extra little push
$3.95
The Tanpan ferrule converts standard Tanpans to Tanpan inlines. - Coverts Tanpan into Tanpan Inline
$4.95
Small parts for Wolf Tooth ReMote.
$4.95
Travel Adjustment Spacers for the Resolve dropper post. The travel height of the dropper post can be reduced in 5 mm increments up to 50 mm height reduction with 10 spacers.
$5.00
CAMO Chainring Bolt Kit are designed specifically for use with CAMO spiders and rings - Includes 5 Torx head M5 x 8mm bolts - ED coated steel is durable - Bolts include a blue Nylok patch for a secure installation - Torque bolts only to 4-5 Nm and use blue Loctite threadlock
$5.00
CAMO Chainring Bolt Kit are designed specifically for use with CAMO spiders and rings - Includes 5 Torx head M5 x 8mm bolts - ED coated steel is durable - Bolts include a blue Nylok patch for a secure installation - Torque bolts only to 4-5 Nm and use blue Loctite threadlock
$5.00
CAMO Chainring Bolt Kit are designed specifically for use with CAMO spiders and rings - Includes 5 Torx head M5 x 8mm bolts - ED coated steel is durable - Bolts include a blue Nylok patch for a secure installation - Torque bolts only to 4-5 Nm and use blue Loctite threadlock
$6.95 - $18.95
Wolf Tooth WT-1 Chain Lube is a synthetic lubricant and a chain treatment in the same bottle. As a synthetic chain lubricant, WT-1 will improve the mechanical efficiency of your drivetrain while lasting 3-5x longer than most other chain lubes. As a chain treatment, WT-1 will clean your chain by pushing dirt and debris to the surface where it can be wiped away. It will also protect your chain in all riding conditions, and allow you to ride longer between applications. - Cleans, lubricates, and protects chains - Peak performance in all conditions, wet and dry - Also works on other places of your bike, including hubs, cables, and jockey wheels
$9.95
This stem cap is where your bike fashion sense and the weight weenie in you collide. This Ultralight and ultra-sleek stem cap integrates a 5mm, 10mm or 15mm headset spacer with your stem cap in finely machined piece. Why have extra steerer tube requiring spacers on top of your stem you ask? Well, many carbon steerers require that the steer tube extend above the stem. Also, riders may want the flexibility to move handlebar height up and down for different types of riding or for bike re-sale. - Design and manufactured in Minneapolis, MN USA - 1 1/8" top (straight 1 1/8" or 1 1/2" to 1 1/8" taper) steerer tubes only - 6061-T6 aluminum - 5mm internal cylinder wall height - Black aluminum bolt included Total weight (cap + bolt): 5mm= 12g. Compare to a standard flat stem cap and steel bolt at 20 grams + spacers add even more.
$9.95
Wolf Tooth Headset Spacers for Trek Knock Block are machined in the USA out of aircraft grade aluminum. - Compatible with Trek Knock Block system - These spacers have unique raised features that key to Knock Block compatible stems (made by Bontrager) - 1 1/8" top (straight 1 1/8" or 1 1/8" to 1 1/2" taper) steerer tubes only
$10.95
Crown races for Wolf Tooth headsets. - For Wolf Tooth headsets
$11.95
Resolve Dropper Post Rebuild Kit includes refill fluid, graduated cylinder, and 10 travel adjustment spacers.
$14.95
Headset bearings for Wolf Tooth headsets. - Replacement bearings
$14.95
Compression plug for Wolf Tooth headsets. - Compression plug works with steerer tube inner diameters ranging from 23.2mm to 24.2mm
$14.95
We think these bolts the best on the market. They have a 5 mm hex socket and are 10 mm long so you can use a bash ring with your 30T x 104 chainring. The bolt length is laser engraved on the head to avoid confusion with shorter bolts. Simply better. No nuts are included with these bolts because the 30t x 104 chainring has threaded standoffs. These work great with Wolf Tooth or any other brand threaded M8 x 0.75 chainrings. Designed and manufactured in the USA from 7075-T6 aluminum alloy. Torque: 6-7 N-m MAX with light grease on the threads only. Product weight - 4 bolts = 4g
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$15.95
Wolf Tooth CenterLock Rotor Lockrings for securing centerlock rotors to centerlock hubs. Machined from 7075-T6 aluminum at Wolf Tooth in Minnesota, USA. - Compatible with 12mm, 15mm and 20mm thru axles and QR - Machined 7075-T6 aluminum - Durable anodized finish - Torque to 40Nm - Not compatible with 6-bolt rotors and hubs - Washer included
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8"steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in the Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$17.95
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in the Minneapolis, MN USA - Fits 1 1/8"" steerers only - Made from 6061-T6 Aluminum
$19.95
8-Bit System is a multi-fonction tools that regroup all potential needs in the field -01 and -02 : 8-Bit Multi-tool plier offer 17 functions: - Master link plier - Valve core wrench; Torx T10 and T25; flat head #3.5; Phillips #2; and hex 2, 2.5, 3, 4, 5,6 and 8mm bits - Includes a tool for clearing tubeless valve stems and a spoke wrench - Storage for one set of quick links -03 : 8-Bit Chainbreaker + Utility Knife Multi-Tool add-on - Chain breaker - L key has a 3mm hex forked tire plug insert - Utility knife - Attach to 8-bit plier with magnets and short pins - Items for internal storage are sold separately -04 : 8-Bit Tire Lever + Rim Dent Remover add-on - Tire lever - Aluminum rim dent remover is designed for use with alloy rims - Attach to 8-bit plier with magnets and short pins -05 : Complete Kit Including Plier and both add-on
$19.95
- Bar end plugs are vital for any bike. - The new Wolf Tooth Alloy Bar End Plugs feature a machined 6061-T6 aluminum end cap, a bolt, and an expandable plastic nut to comprise a lightweight, secure bar end plug option. - Available in eight colors that match existing anodized Wolf Tooth headsets, seatpost clamps, chainring bolts, and more - It is compatible with drop bars and MTB bars.
$19.95
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Single bottle mount with two slotted holes for adjustments up to 4mm +/- 10mm - Designed to maximize bottle capacity on small frame bikes and dual suspension frames
$19.95
The Wolf Tooth Bottle Shift is designed to offset a bottle to a more optimal location and make it possible to also mount a pump on frames with large downtubes. It is most commonly used on dual suspension frames where the water bottle is difficult to access because of interference with the top tube or shock. By shifting the bottle slightly off center and tilting it outward, clearance is greatly improved. - Slots and extra tapped holes in the mount provide 18mm of bottle position adjustment - Designed to be easily flipped to provide either left or right hand bottle access - Centerline of the bottle moves 18mm with the combined 10 degree tilt and 9 mm offset - Offset of pump bracket mounting holes allows mounting mini pumps on most mountain bikes
$19.95
Designed for the XC racers. 5mm of 100% silicone compound provides excellent vibration dampening and superior comfort. - 100% Silicone weather resistant material - Plastic bar end plugs - 5mm thick
$19.95
Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required
$19.95
Headset bearings for Wolf Tooth headsets. - Replacement bearings
$19.95
These bolts are designed as a direct fit for 30 Tooth x 104 BCD threaded chainring. These are alloy bolts with 4mm hex heads and 10mm length. - Designed for M8 x .75 thread pitch - 10mm long - 4mm hex head - Bolt length is laser engraved onto the bolt head for easy length identification - 6-7 Nm installation torque with light grease on threads only
$19.95
We think these bolts and nuts are the best on the market. Other short bolts/nuts designed for single rings use a slotted nut that is likely to strip-out the first time you use it. Ours use a large hex socket on both the bolt (5 mm) and the nut (6 mm). Bolts are 6 mm long and have the length laser engraved on the head. Simply better. These work great with Wolf Tooth or any other brand single chainrings. Designed and manufactured in the USA from 7075-T6 aluminum alloy. Torque: 6-7 N-m with light grease on the threads only. Product weight: 4 bolts = 7g
$21.95
Slightly thicker than the Razer Grips, slightly thinner than the Fat Paw Grips, these 6.5mm thick grips are great for longer rides, as they reduce hand fatigue and finger numbness. - 100% proprietary dual-density silicone compound provides excellent vibration damping and conforms to your hand for improved comfort while maintaining durability - Tacky texture provides excellent grip with or without gloves in all weather conditions - 6.5mm thick
$21.95
Roadlink Rear Derailleur Part - The RoadLink is optimized for use with ten or eleven-speed 11-36t and 11-40t cassettes - 11-42 or 10-42 setups are not supported - Works with all 10-11 speed Shimano and SRAM Road Derailleurs - Best used with Single or Double Setups - see manufacturer's site for more details
$22.95
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Three slots for additional adjustments over the B-RAD 2 base - Compatible with triple bottle mounts on forks or frames, use neoprene pad and zip tie for use with standard bottle cage mounts
$22.95
Ergonomic silicone grips from Wolf Tooth. - Multi-position ergonomic design - Unique design increases grip and comfort while climbing
$24.75
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$24.75
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$24.75
Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum
$24.95
B-RAD, which stands for Bottle Relocation and Accessory Device, is a system for organizing on-bike accessory storage using bottle cage mounts. Used alone to shift bottle cage location for clearance, or combine with other B-RAD accessories to carry tools, tubes pumps or a 2nd bottle on downtubes. - Long, four-slotted mount allows two, smaller bottles to be mounted in-line - Compatible with triple bottle mounts on forks or frames, use included neoprene pad and zip tie for use with standard bottle cage mounts
$24.95
B-RAD Bottle Mounts allow for cargo customization and cargo optimization. They are designed to work in tandem with B-RAD Base mounts to keep cargo on the bike and off the back. - Compatible with any bike frame that has 2 standard 64mm spacing bottle cage mounts (most modern frames) - 6061-T6 aluminum brackets, stainless hardware - Weight (no hardware) – 20g - Maximum load 1700g - Designed to carry two bottles or accessories off of one B-RAD base
$24.95
B-RAD Everywhere Base 2
$24.95
B-RAD Half Bottle Mounts allow for cargo customization and cargo optimization. Designed to work in tandem with B-RAD Base, the Half-Bottle Adaptor moves the bottle over about half a bottle radius to make it easier to access. The Accessory strap mounts can be mounted to the other side providing a mounting point for additional items. - Mounts to the B-Rad base mount (not included
$24.95
- 4-way-stretch woven spandex glove back and articulated fingers for flexibility and fit - Amara palm and double stitch thumb reinforcement for durability - Touch-screen Ax Suede patch - Silicone Gripper palm and fingers provide a superior grip - Neoprene cuff for a comfortable and secure fit
$24.95
The Wolf Tooth Morse Cage has its name because of the dots and dashes on the mounting plate that provide for up to 32mm of vertical placement adjustment. This allows the rider to change bottle cage position based on restrictions of frame size, frame bags, or mount placement. - Hand-bent hollow tubing - Fits any bike frame that has two standard bottle cage mounts with 64mm spacing - Easily bent back in to shape if damaged - Made by hand in Minnesota
$24.95
Replacement Bar Plugs for the WTC Singletrack Pogie. - Quick install and removal of pogies via proprietary quarter turn bar plug mounting system
$24.95
These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only
$24.95
These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only
$24.95
These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only
$24.95
These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only
$24.95
These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only
$24.95
Goatlinks are designed to optimize the derailleur's position relative to your cassette. Offered in two versions - a 10-speed and 11-speed, each is intended to improve the shifting of your 1x drivetrain.
$24.95
The precision-engineered Wolf Tooth Seatpost Clamp secures your seatpost and looks good doing it. At the heart of the Wolf Tooth Seatpost Clamp is a custom self-aligning bolt and anchor. The M5 bolt includes spherical washer and mates with a cylindrical anchor barrel. This means that threads are always perfectly aligned, preventing binding and ensuring consistent clamping force. - M6 stainless steel bolt with integrated washer - Tool interface - 4mm hex key
$24.95
The precision-engineered Wolf Tooth Seatpost Clamp secures your seatpost and looks good doing it. At the heart of the Wolf Tooth Seatpost Clamp is a custom self-aligning bolt and anchor. The M5 bolt includes spherical washer and mates with a cylindrical anchor barrel. This means that threads are always perfectly aligned, preventing binding and ensuring consistent clamping force. - M6 stainless steel bolt with integrated washer - Tool interface - 4mm hex key
Page 1 of 5 Next page