The Deluxe Wall-Mount Repair Stand easily mounts to any post or wall stud. This shop-quality stand places the bike approximately 14.5 inches from the wall, so you'll have plenty of work space. The awesome clamp is Park's Adjustable Linkage model, which feature's replaceable rubber jaws; fits seatposts and frame tubes from 1 to 1 5/8-inch diameter; includes recesses for cable housing and rotates 360 degrees for optimum bike positioning. This great stand lets you work on your bikes just like a pro and is built to last.
Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.
Traveling mechanics choose the Super-Lite Team Race Stand because this Euro-style stand securely holds bikes without clamping the frame tubes or seatpost but by gripping the front or rear dropouts via quick releases. This is ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching, this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). Plus, the gossamer 13.5-pound weight makes it the ideal choice for traveling mechanics everywhere.
The SBK-1 is a professional level kit for installing and removing cartridge bearings in bicycle suspension pivots. A comprehensive set of 27 precision-machined hard-anodized guides enables compatibility with a wide range of bearing inner and outer diameters. Combined with our proven bearing press design, the SBK-1 quickly and easily pushes the old bearing out of the linkage and reinstalls the new bearing precisely and squarely. - Magnetic back plate for easy configuration and assembly - Organized in a convenient storage case Includes extractor cups/drifts for the following ODs: - 16mm - 17mm - 19mm - 20.6mm - 21mm - 22mm - 22.3mm - 24mm - 26mm - 28mm - 28.6mm - 30mm - 32mm - 35mm Includes extractor studs and pilots for bearings with the following IDs: - 8.5–9mm - 10mm - 12mm - 12.7mm - 15mm - 17mm - 20mm NOTE: For bearing extraction, the SBK-1 requires a minimum of 3mm of flat linkage structure outside the bearing to support the extractor cup/drift. For bearings without this flat structure, consider using the Park Tool SHX-1 Slide Hammer Bearing Extractor.
The Deluxe Wall-Mount Repair Stand easily mounts to any post or wall stud. This shop-quality stand places the bike approximately 14.5 inches from the wall, so you'll have plenty of work space. The awesome clamp is Park's Professional Micro-Adjust model, which features replaceable rubber jaws; fits seatposts and frame tubes from 7/8 to 3-inch diameter; includes recesses for cable housing and rotates 360 degrees for optimum bike positioning. This great stand lets you work on your bikes just like a pro and is built to last.
$209.88 - $271.32
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
- Precision tool for quickly and easily removing the headset crown race from the crown race seat of the fork - Fully adjustable, allowing precise, independent positioning of each blade around the crown race for flexibility in fitting around crown race interferences - Works with 1,1-1/8,1-1/4,1.5" forks (suspension or rigid) and crown races with outside diameters up to 64mm - Accepts steerers up to 430mm - All steel construction for long life
Park's Bench-Mount Repair Stand easily bolts to any workbench and includes Park's shop-quality solid cast-aluminum Adjustable-Linkage Clamp that boasts durable, protective and replaceable vinyl jaw covers. The clamp holds seatposts and frames from an inch to 1 5/8 inches in diameter and there are slots for cables, too. Plus, this stand rotates 360 degrees for optimum bike positioning.
Park Tool's Fork Threading Set is designed for cutting new threads and for chasing existing threads on fork columns that are not chromed. The FTS-1's expandable cutting dies are made from the highest quality high-speed steel for precision cutting and long life. The unique thread guide system used with the FTS-1 is specially designed to allow the metal chips and shavings that result during use to fall completely through the guide, preventing damage to the fork threads and the tool. The FTS-1 includes: • Die handles • 1" x 24 tpi cutting die (Part #606) • 1" cutting guide (Part #610) Accessory dies and guides are also available separately: • 1-1/8" x 26 die (Part #607) • 1-1/8" guide (Part #611) • 1-1/4" x 26 die (Part #608) • 1-1/4" guide (Part #612) Die handles fit all three sizes of dies and guides.
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.
"A full-featured bicycle workstand designed and built for the home mechanic. The PCS-10.3 includes Park Tool's tried and true cam-actuated micro-adjustable clamp design for quick one-handed entry and exit, as well as a quick-release height adjustment lever for easy, secure adjustment. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with tubular support braces, a locking support yoke, and upgraded internals for extra dependability. The PCS-10.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes. The PCS-10.3 features an integrated height-adjustable parts tray, as well as accessory ports for the Park Tool #106 Work Tray or PTH-1 Paper Towel Holder (both sold separately), so your tools and small parts are always within reach. Quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-10.3 is the perfect way to upgrade your home shop—a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. NOTE: The maximum weight capacity of the PCS-10.3 assumes the weight is centered below the clamp and between the legs.? - Cam-actuated micro-adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Rubber saddle pad allows bikes to be hung by the saddle for quick adjustment or storage - Durable, textured powder coat finish - Integrated height-adjustable parts tray - Height adjustment collar features accessory ports for compatibility with the #106 Work Tray or PTH-1 Paper Towel Holder (both sold separately) - Maximum weight capacity*: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) using convenient quick-release lever - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 45"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg)"
Keep your precious bicycle tools safe and secure when traveling to cycling events with Park's Blue Box Tool Case. It boasts a dent-proof composite shell supported by a tough, light aluminum frame. Inside are removable tool boards made with durable 600D ballistic nylon sewn to an ABS inner panel. You get 35 tool pockets and straps that accommodate a wide variety of tools. Plus, there's a lower compartment with adjustable partitions so you can customize your layout. The front board also detaches and hangs off the outside of the case so you can set up your full shop and see and access all your tools at once. And, since tools have that terrible tendency to wander when traveling, the Blue Box is lockable with both a combination and a key.
Perfect for taking to races and rides, the Portable Workbench is a bench that folds for easy transport and storage. It features a large work surface with specially sized slots, holes, and recesses and for holding tools, shop towels, lubes, beverages, etc. The folding steel legs provide a solid base for a toolbox and supplies, too.
The Team Race Stand is a Euro-style stand that securely holds your bike without clamping the frame tubes or seatpost but by holding it by either the front or rear dropouts via quick releases. It's ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). This great stand was originally designed for the mechanics of the pro peloton, and is now available to home mechanics everywhere. Plus, the stand folds down to 33-inches long, so you can easily throw it in the back of your car.
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-5C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing, and feature replaceable jaw covers. - Fits PCS-4, PRS-5, PRS-6, and PRS-7 stands made after 6/96 - Fits bike frame tubes from 1" to 1 5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.
Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-3C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits all generations of PRS-2, PRS-3, and PRS-4 stands, and PRS-5 stands manufactured before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-9C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits PRS-6, PRS-7, and PRS-8 stands made before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.
For all your bicycle repairs, choose Park's Home-Mechanic Repair Stand! This great stand is always at the ready with fast and easy set-up and take down. The sophisticated cam-type clamp allows single-action clamping of tubes 7/8 to 3 inches in diameter, and the clamping pressure is fully adjustable to prevent frame damage. You'll love the smooth 360-degree rotation while the quick-release height adjustment (39 to 57 inches) makes this stand perfect for any height rider. Plus, this fine stand folds down to 41 inches for portability and easy storage.
Park's Bench-Mount Repair Stand easily bolts to any workbench and includes Park's shop-quality Micro-Adjust Clamp that handles round and aero seatposts and frames from 7/8-inch to 3-inches in diameter and clamps securely with its quick-release cam and handle that fine-tunes the tension. The clamp also has protective rubber jaws and built-in slots for cables. Plus its jaws are only 2.7 inches tall so they easily fit in narrow areas like on seatposts that aren't raised much. This stand rotates 360 degrees for optimum bike positioning, too.
"The PCS-9.3 is a basic folding bicycle workstand designed and built for the home mechanic – a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with a locking support yoke and upgraded internals for extra dependability. The PCS-9.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes.* The PCS-9.3 quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-9.3 is the perfect way to upgrade your home shop. NOTE: The maximum weight capacity of the PCS-9.3 assumes the weight is centered below the clamp and between the legs.? - Fully adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Durable textured powder coat finish - Maximum weight capacity: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 44"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg) - #2848A quick-release collar with accessory pods required for use of PTH-1 Paper Towel Holder or 106 Work Tray"
A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench
Upgrades the DT-5 to the DT-5.2. - Four telescoping axle adaptors - Two stand off studs for Flat Mount alignment - 12mm front fork thru axle sleeve
$151.12 - $187.82
After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
A bench-mounted version of our popular PCS-10.2 Deluxe Home Mechanic Repair Stand. Features our world-famous cam-actuated micro adjust clamp design, which securely holds bicycles in place while allowing quick installation and removal. - Cam actuated, micro-adjustable clamp allows quick entry and exit and fits 1-inch to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - Narrow clamping jaws (2.7-inch/7cm) fit into tight areas or on short seat posts - 360° infinite clamp rotation allows bike to placed in optimal position for specific repairs - All-steel structure for maximum stiffness and durability - Super strong glass-filled nylon-composite fittings and top tube internals enable smooth rotation and secure positioning - Mounts to any flat surface (mounting bolts not included) Distance from the center of the clamp to the center of the mount is approximately 11 3/4-inch (30cm). Height from bench to center of the clamp axis is approximately 9 7/8-inch (25cm). Weight Limit: The PCS-12.2 Home Mechanic Bench Mount Repair Stand has an 80 lb. (36kg) weight limit, provided the stand is securely mounted with appropriate fasteners to a solid and secure bench surface. The user is responsible for making sure the workbench and the fasteners are capable of handling this amount of weight.
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.