$9.14 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool's Tool Tray Collar easily adapts the #106 Work Tray to fit the 41mm upright tube on 2011 and older PRS-20 and PRS-21 Repair Stands, as well as 1996 and newer PCS-1, PCS-4, PCS-4-1 and PCS-4-2 Repair Stands (each sold separately).
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Prevents handlebar and front wheel from rotating or moving when the bike be stored or fixed.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.
Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Portable Wheel Dishing Tool is a must. It disassembles quickly for storage or travel and allows you to easily check centering on road, mountain and BMX wheels from 24 to 29 inches in diameter and it works with any hub. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Park's Cast Aluminum Tool Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools, lubes and small parts close at hand. It has deep sides so your small items stay put, a holder for cans of lube and slots for holding your tools. This handy tool fits Park's PRS-2, PRS-3, PRS-6, PRS-13, PCS-1, PCS-1 and PCS-4 repair stands manufactured after June 1996 (stands sold separately).
For anyone who doesn’t want to be confined to parking lots or trailheads — adventurers, racers, and garage mechanics — Küat designed the Tri-Doc for you. Tri-Doc offers an affordable way to turn your NV 2.0 into a travel stand. Reliable tri-leg design creates a stable platform for needed tune-ups or repairs. Aluminum construction finished with polished anodizing pairs perfectly with your NV 2.0. - Portable telescoping design - Quick setup - Pairs with your NV 2.0 Trail Doc - Anodized finish reflects NV 2.0 - Rubber feet offer additional stability and protection
Topeak's LineUp Stand securely holds your bike by the rear wheel for storage or display. Its spring-loaded arm automatically adjusts to fit wheels from 20-inches to 29-inches in diameter. Use it at home to store your bike, or use it to hold your pit bike at your next cross race!
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
Park's Home Mechanic Wheel Truing Stand allows extremely accurate and reliable wheel truing and even building at an economical price. It's constructed from heavy-gauge steel and works with most wheel sizes and hub widths. It can be bolted to a bench for additional stability.
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
Park's Bench Mount Home Mechanic Repair Stand features a quick adjusting cam-type clamp that fits on frame tubes up to 76mm in diameter. Plus, the clamp rotates 360 degrees for access to any part of the bike for easy repairs. The clamping pressure is fully adjustable, too, to prevent damage to lightweight frame tubes. Plus, this excellent stand boasts a durable powdercoat finish, protective rubber jaws, and it mounts to any flat surface (bolts sold separately), so you can turn just about any nook and cranny in your house or garage into a proper bike repair facility!
Hirobel is a specially designed clamp for bicycle repair stands that makes it easier to work on your bike. It better distributes stresses and loads through the bicycle frame, offering superior stability while eliminating possible crushing or damage to thin-walled and shaped tubing. The pressure clamps used on contemporary workstands were developed for round steel tubing more than 40 years ago, predating carbon fiber, aluminum, aerodynamic and oversized tube shapes, integrated seat masts, dropper posts, and suspension systems. These legacy designs assume your bicycle tubing to be both round and straight, and when it is not, the clamp can impart very high point loads at the clamp edges causing finish damage, internal carbon layup damage, or outright crushing of tubes on the lightest designs. With Hirobel, specially shaped, paint-friendly cones and bindings cradle the frame at the tube intersections, where wall thicknesses are higher and forces can be distributed over much larger surface areas. Adjustable and adaptable for any possible frame design, the Hirobel also allows the repair stand clamp to be located closer to the bicycle center of gravity. This improves stability and eliminates bouncing of the bike during heavier work while also locating the drivetrain consistently higher for the mechanic, improving visibility while reducing back strain.
$151.12 - $187.82
After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments
The Home Mechanic Repair Stand offers Park Tool quality in an entry-level repair stand for home mechanics. The 3-point leg system and adjustable height (from 39 to 57 inches) create a stable, ergonomic repair station for easy, efficient wrenching. Plus, the great clamp fits seatposts and frame tubes from 7/8 to 3 inches in diameter, has replaceable protective rubber jaws and rotates 360 degrees for easy access to all parts of your bike. It will also clamp round and aero seatposts. This stand even folds to 41 inches for easy portability and storage.
- Clamp height adjusts from 41.75"- 56.75" (106 to 144 cm) to allow you to work at a comfortable level - Clamp head rotates 360° - The articulating jaw on the clamp provides a large clamp opening, allowing the bike to be easily inserted and removed by flipping the cam lever. - Clamp head is micro-adjustable to accommodate various tube sizes. - No tools required for quick setup and storage - Lightweight aluminum construction - Product Weight: 13.6 lbs (6.18 kg) - Max load capacity: 77 lbs (35 kg)
A bench-mounted version of our popular PCS-10.2 Deluxe Home Mechanic Repair Stand. Features our world-famous cam-actuated micro adjust clamp design, which securely holds bicycles in place while allowing quick installation and removal. - Cam actuated, micro-adjustable clamp allows quick entry and exit and fits 1-inch to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - Narrow clamping jaws (2.7-inch/7cm) fit into tight areas or on short seat posts - 360° infinite clamp rotation allows bike to placed in optimal position for specific repairs - All-steel structure for maximum stiffness and durability - Super strong glass-filled nylon-composite fittings and top tube internals enable smooth rotation and secure positioning - Mounts to any flat surface (mounting bolts not included) Distance from the center of the clamp to the center of the mount is approximately 11 3/4-inch (30cm). Height from bench to center of the clamp axis is approximately 9 7/8-inch (25cm). Weight Limit: The PCS-12.2 Home Mechanic Bench Mount Repair Stand has an 80 lb. (36kg) weight limit, provided the stand is securely mounted with appropriate fasteners to a solid and secure bench surface. The user is responsible for making sure the workbench and the fasteners are capable of handling this amount of weight.
- Clamp can be positioned at 5 directions. - Adjustable in height, 105 - 150 cm. - Max load: 50 kg
Being a "shade tree mechanic" doesn't mean you should lean your bike against a tree. You paid hard-earned money for your family's bike collection and we've got a budget-conscious, yet feature-loaded bike repair stand that's perfect for the home bike mechanic. The price-point leading 360-degree rotating clamp can position your bike optimally for any work you're planning. Plus, the Recreational Stand leverages a 52-inch (132cm) wide base with rubber-coated end caps for fantastic stability on any surface. And when the service day is done, it folds into a space-saving unit for storage. Add a Tool Tray, Bottle Opener and a Pro Truing Stand for the complete at-home bike shop. - Seatpost clamp features Spinner Knob for quick closure and precision clamping pressure - 360-degree rotating clamp design provides easy access to any part of your bicycle - Fixed clamp height at 55-inch (139cm) - Rubber-coated clamp secures and protects expensive components and beautifully painted frames - Clamp opening up to 1.9-inch (4.8cm) accommodates even the largest diameter frame tubes - Powder-coated steel construction is corrosion resistant and incredibly durable - Stiff 52-inch (132cm) base and rubber-coated end caps create ultimate stability even on uneven surfaces - Total load capacity of 60lbs (27.2kg) accommodates service on most road, mountain bikes, fitness bikes, and electric bikes - Portable and compact construction creates a remarkably small folded footprint of 10 x 4 x 55-inches (25.4 x 10.2 x 139.7cm) - Optional Travel Bag available - At 13.8lbs (6.3kg), moving in and out of storage is no problem - No assembly required - 3-year Warranty
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
Page 1 of 3 Next page